pneumatic Archives

Working Principle of Pneumatic Globe Valve

July 7, 2021

Principle of Pneumatic Globe Valve, Working Principle of Pneumatic Globe Valve
Working principle of pneumatic stop valve:
Pneumatic shut-off valve is a valve that uses compressed air as the power source. It adopts remote control. The main control room manually or automatically triggers the action command to activate the inlet and exhaust solenoid

pneumatic globe valve

valves to supply and discharge compressed air into the actuator. Compressed air acts on the piston or diaphragm to overcome the frictional force of the valve action and the spring force on the valve stem, thereby depressing (for the loss of air to open the valve) or lifting (for the loss of air to close the valve) the valve stem, driving the valve core to move up and down , Make the valve open or close. When the valve loses air and there is no compressed air in the drive head, the valve will be in a safe position of fully open or fully closed according to the requirements of the system. Compressed air for power plant instruments, the supply pressure is generally 4-9bar. Before entering the valve, the compressed air is first filtered and purified through the filter, and then reduced by the pressure reducing valve. The reading of the inlet pressure gauge does not exceed 4bar. Pressure adjustment can be achieved by adjusting the adjustment screw installed on the top of the pressure reducing valve, and the protective cover must be loosened before adjustment.
Pneumatic globe valve installation instructions:
Pneumatic shut-off valve is usually used in fully closed and fully open gas and liquid unidirectional flow pipelines. It has a longer structure and shorter length than gate valves. When the medium is highly corrosive, a low-inlet and high-outlet stop valve should be used. When the medium pressure is high or the valve stem is frequently opened and closed, the valve stem should be thickened to avoid bending of the valve stem caused by the thrust of the medium. Compared with other valves, the flow resistance of the pneumatic shut-off valve is larger. Pay attention to the problems of the air source pressure and the pressure and corrosion resistance of the valve stem during use. Pneumatic shut-off valve is not suitable for media with particles, high viscosity and easy to coke.

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

Working Principle of Pneumatic Gate Valve

June 29, 2021

Brief introduction of pneumatic gate valve:
The pneumatic gate valve is equipped with a pneumatic actuator, which is driven by compressed air to control the gate valve. The valve core is composed of a wedge-shaped structure and a parallel structure, which is suitable for the emergency cut-off and discharge of gas and liquid pipelines.

pneumatic gate valve (3)

Working principle of pneumatic gate valve:
When using the air source to operate the gate valve, the small handle of the manual device must be turned to the pneumatic position to open and close the nut and the screw rod. When the compressed air enters from the upper pipeline of the cylinder, the piston and the piston rod in the cylinder are pushed straight When the compressed air enters from the lower pipe, the gas pushes the piston and piston rod in the cylinder to move upwards, and at the same time drives the valve stem to move upwards to open the valve. When there is no air source, the screw rod and the opening and closing nut can be used to open and close the valve. First, the upper and lower intake pipes of the cylinder are in the exhaust state, and the small handle of the manual part is in the manual position, so that the opening and closing nut and the screw are in the manual position. In the normal meshing state, turn the large handwheel at the manual part at this time. When the handwheel is turned clockwise, the valve is closed, and when the handwheel is turned counterclockwise, the valve is opened. When the air source is introduced from the upper air inlet, the valve stem drives the valve plate to move downward, and the valve is closed.
When the air source is introduced from the lower air inlet, the valve stem drives the valve plate to move upward, and the valve opens.
Pneumatic gate valve parameters:
Actuator: cylinder piston structure;
Optional accessories: manual device, filter, solenoid valve, echo device, control box;
Main material: ductile iron, cast steel, stainless steel; Caliber: DN50-500;
Pressure: PN1.6-6.4mpa;
Temperature: Q-29～350℃, C-29～450℃, P-30～540℃;
Medium range: water, steam, petroleum, gas, fluid, medium containing hard particles and impurities.

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6

Pneumatic U-shaped flange butterfly valve

July 22, 2020

Introduction of Pneumatic U-shaped flange butterfly valve:

U type flange butterfly valve (8)

The pneumatic U-shaped butterfly valve adopts a top-mounted structure, which reduces the connecting bolts of the valve body under the conditions of high pressure and large diameter, enhances the reliability of the valve and can overcome the influence of the weight of the system on the normal operation of the valve.

Scope of application of Pneumatic U-shaped flange butterfly valve:
Pneumatic U-shaped butterfly valve is widely used in coal chemical, petrochemical, rubber, paper, pharmacy and other pipelines as media splitting, confluence or flow switching devices.

The main parameters of Pneumatic U-shaped flange butterfly valve:
Nominal diameter of pneumatic U-shaped butterfly valve: DN50mm-DN300mm;

Nominal pressure of pneumatic U-shaped butterfly valve: PN1.0MPa-1.6MPa;

The temperature range of pneumatic U-shaped butterfly valve: -29℃-300℃.

Tanghai Valve is the best manufacturer of U-type butterfly valve in China. We produce the best quality products with competitive low prices.

Tianjin Tanghai Valve Manufacturing Co., Ltd. is one of the largest butterfly valve manufacturers in China, main products are butterfly valves, check valves

Main products: butterfly valve, lug type butterfly valve, wafer type butterfly valve, U-type butterfly valve, double flange butterfly valve, gate valves, check valves, globe valves, valve parts (Valve body, Valve disc, Valve shaft, Valve seat…)

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

Posts

Working Principle of Pneumatic Globe Valve

Working Principle of Pneumatic Gate Valve

Pneumatic U-shaped flange butterfly valve

TH VALVE • PROFESSIONAL VALVE MANUFACTURER

GET IN TOUCH WITH US

Tag Archive for: pneumatic

Posts

TH VALVE • PROFESSIONAL VALVE MANUFACTURER

GET IN TOUCH WITH US